Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
The article following next involving How to Install a Bathtub is indeed intriguing. Check it out for yourself and see what you think of it.
Setting up a tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily easily accessible, the task can relocate quickly; if you need to open up a wall to remove the old bathtub and also position the new tub, the job is much harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to vacate the old bathtub and set in the brand-new one. See to it you have qualified yourself for the task and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This write-up will certainly help you install a new bathtub in your restroom if you have actually currently gotten a brand-new tub as well as do not require to transform the setup of your previous water pipelines.
Your devices and also product list need to consist of the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be rather problematic because of the restricted accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel all set for the staying water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, put the bath tub in the required setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit all-time low of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub must wait up until the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making sure that the washers are in place between the tap and also the sink. Safeguard the faucet in position with the producer offered backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, bring about issues with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is a good idea to fit the tiles making use of water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that article on How to Install a Bathtub Yourself through a good friend on our other web blog. Sharing is nice. You never know, you may be doing someone a favor. Kudos for your time. Come back soon.
Schedule
Report this page